lựa chọn dung dịch làm mát khoan carbide. Nhận ngay Measurement over Pins (mm), Dovetail Width (mm) cho thông số gia công của bạn.
Rãnh Đuôi Én isn't just an academic exercise — it's a daily decision point across three major machining sectors. Each industry brings its own challenges, và tooling suppliers like Kennametal, OSG, và Seco Tools have developed grade-specific responses.
Ti-6Al-4V và Inconel 718 chi phối ở đây. Kennametal cấp được thiết kế riêng cho vật liệu HRSA hoạt động ở khác biệt đáng kể Rãnh Đuôi Én windows than general-purpose grades. A Hermle 5-axis cell machining engine mounts needs reliable Rãnh Đuôi Én — there's zero tolerance for tool failure at $50K per raw forging.
Sản xuất số lượng lớn đĩa phanh CGI và vỏ mô-tơ điện đẩy Rãnh Đuôi Én đến giới hạn. OSG ceramic and CBN grades run at SFM levels that carbide can't touch. Cycle time is everything — a 2-second per part Rãnh Đuôi Én optimization can save $180K+ annually on a 500K-unit line.
Cấy phẩm gối cobalt-crom và lồng sống Ti cần bề mặt hoàn thiện tinh khiết. Seco Tools's dao phay đầu carbide hạt mịn, chạy ở bảo thủ Rãnh Đuôi Én, deliver the Ra <0.4µm required. Tool change frequency is secondary to process reliability — an unexpected insert failure mid-cut means a scrapped implant.
Cùng nguyên lý Rãnh Đuôi Én principle applies across all three sectors, but the optimization target shifts dramatically: aerospace prioritizes process security, automotive prioritizes speed, và medical prioritizes surface integrity. Your Kennametal, OSG, hoặc Seco Tools rep can help you tune for your specific application.
Dovetail slides and grooves are measured indirectly using precision pins (or wires) and a micrometer. The measurement over pins method provides an accurate check of the dovetail angle and width without needing an optical comparator.
The angled flanks of a dovetail cannot be measured directly with a micrometer. Pins of known diameter contact the flanks at a tangent point, converting the angular measurement to a linear one. This is the standard QA method for dovetail slides and O-ring grooves.
The pin should contact the flanks near mid-height. A good rule: pin diameter ≈ 0.5× dovetail height. Common choices: 2 mm pins for small dovetails (under 5 mm height), 3-5 mm for medium, 6-10 mm for large machine slides.
Dovetail cutters produce angled walls (typically 45 deg or 60 deg ). T-slot cutters produce a T-shaped undercut with parallel walls. Both are used for workholding slots, but dovetails provide self-aligning sliding fits while T-slots accept T-nuts for clamping.
Enter the dovetail width (at the narrowest point), height, and angle. The calculator gives the measurement over pins. Use this to set your micrometer or caliper when inspecting dovetails. For female dovetails, subtract the pin contribution instead of adding.
Continue with closely related tools from the machining calculator library.
Gửi cho chúng tôi vật liệu chi tiết, loại nguyên công, kích thước lô và yêu cầu dung sai. Chúng tôi sẽ kết nối bạn với nhà máy phù hợp và có giá trong vòng 48 giờ.
Khám phá thêm công cụ và máy tính gia công chính xác