yêu cầu độ bóng bề mặt chi tiết hàng không. Nhận ngay Total Cost, Cost per Part cho thông số gia công của bạn.
Even with high-end tooling from Sandvik Coromant and Nachi, things go wrong. Here are the most common Trọng Lượng & Chi Phí Kim Loạiphổ biến nhất đội ngũ kỹ thuật gặp phải, và cách khắc phục.
Chẩn đoán: surface speed is likely too high. Even Sandvik Coromant AlTiN-coated carbide can't outrun excessive heat generation. Check that your Trọng Lượng & Chi Phí Kim Loại có khớp với độ cứng vật liệu thực tế — thay đổi từ HRC 28 sang HRC 32 trên 4140 thay đổi mọi thứ.
Khắc phục: Reduce SFM by 15-20%. Verify coolant concentration with a Hexagon refractometer (target 8-10% for steel).
Chẩn đoán: Trọng Lượng & Chi Phí Kim Loại might be fine for straight cuts, but corner engagement increases dramatically. Nachi application engineers call this the "corner trap" — the tool sees 180° of engagement in a 90° internal corner.
Khắc phục: Thêm một lượt hoàn thiện ở độ sâu bán kính 0.1mm với dụng cụ hoàn thiện riêng. Lập trình Grob giảm tốc độ tiến xuống 50% ở các góc.
Chẩn đoán: You're applying Sandvik Coromant Trọng Lượng & Chi Phí Kim Loại values to Nachi tools — hoặc vice versa. Each manufacturer's carbide substrate and lớp phủ system has a different sweet spot.
Khắc phục: Tải xuống biểu đồ Trọng Lượng & Chi Phí Kim Loại chart for your exact tool from the manufacturer's website. Sandvik Coromant CoroPlus and Nachi NOVO both offer free digital tools.
Material cost is often the largest single component of a machined part cost. This calculator multiplies the part weight by the material unit price, with an estimate for the number of parts produced from the material input.
Titanium (Grade 5/Ti-6Al-4V) at $30-50/kg. Inconel 718 at $40-60/kg. Tungsten carbide blanks at $80-200/kg. At the low end: mild steel at $1-2/kg, aluminium 6061 at $3-5/kg. Prices fluctuate with commodity markets and order quantity.
Typical buy-to-fly ratios: 4:1 to 10:1 meaning 75-90% of the purchased material becomes chips. For simple parts from bar stock, 15-30% waste. For complex aerospace structural parts machined from plate, 85-95% waste. Use the scrap value calculator to offset some of this cost.
Calculate the blank weight (not finished part weight), multiply by material price, then divide by estimated parts per blank. Compare the total including tooling cost, cycle time, and scrap. The cheapest material is not always the lowest cost per part if it machines slowly or wears tools quickly.
Enter the material weight in kg and the price per kg. The calculator shows the total material cost and an estimated cost per part. For accurate quoting, add waste allowance, shipping, and minimum order quantity surcharges to the base material cost.
Continue with closely related tools from the machining calculator library.
Gửi cho chúng tôi vật liệu chi tiết, loại nguyên công, kích thước lô và yêu cầu dung sai. Chúng tôi sẽ kết nối bạn với nhà máy phù hợp và có giá trong vòng 48 giờ.
Khám phá thêm công cụ và máy tính gia công chính xác